Best Diy Quadcopter out of top 23

 

QWinOut Radio 433MHz 100mw Telemetry Kit for 3DRobotics 3DR Standard Version APM APM26 Pixhawk 246 FC DIY Quadcopter FPV

QWinOut Radio 433MHz 100mw Telemetry Kit for 3DRobotics 3DR Standard Version APM APM2.6 Pixhawk 2.4.6 FC DIY Quadcopter FPV

QWinOut Radio 433MHz 100mw Telemetry Kit for 3DRobotics 3DR Standard Version APM APM2.6 Pixhawk 2.4.6 FC DIY Quadcopter FPV - 3dr telemetry kit specifications, very small size, light weight (under 4 grams without antenna), 915mhz/433 mhz, receiver sensitivity to -121 dbm, transmit power up to 20dbm (100mw), transparent serial link, air data rates up to 250kbps, mavlink protocol framing and status reporting, frequency hopping spread spectrum (fhss), adaptive time division multiplexing (tdm), support for lbt and afa, configurable duty cycle, built in error correcting code (can correct up to 25% data bit errors), demonstrated range of several kilometers with a small omni antenna, can be used with a bi-directional amplifier for even more range, open source firmware, at commands for radio configuration, rt commands for remote radio configuration, adaptive flow control when used with apm, based on hm-trp radio modules, with si1000 8051 micro-controller and si4432 radio module.

 

2Pcs DIY Quadcopter Plastic Propellers Prop 6 Inch for RC Airplane

2Pcs DIY Quadcopter Plastic Propellers Prop 6 Inch for RC Airplane

2Pcs DIY Quadcopter Plastic Propellers Prop 6 Inch for RC Airplane - Total length(rotating diameter) 6″hub thickness 15mm / 059″. Vane model 6″motor shaft hole dia 25mm / 01″, 1mm/ 004″. Material plasticcolor orange. Product name rc airplane propellersvane number 2. Weight 8gpackage content 2pcsx rc airplane propellers.

 

iFLY 2 pcs 1 set 1 Pair 58GHZ24GHZ TXRX FPV Antenna Mushroom RP-SMA Male diy quadcopter

iFLY 2 pcs 1 set 1 Pair 5.8GHZ/2.4GHZ TX/RX FPV Antenna Mushroom RP-SMA Male diy quadcopter

iFLY 2 pcs 1 set 1 Pair 5.8GHZ/2.4GHZ TX/RX FPV Antenna Mushroom RP-SMA Male diy quadcopter - Vswr . Horizontal beamwidth 15-25 vertical beamwidth 15-25 directional diagram vertical connector location bottom. 58 ghz mushroom antenna for transmitter and receiver greatly increase the range and covering of your wireless video transmitting and receiving system.

 

Hobbypower CNC Superlight Alloy 16mm Arm Clamp Tube Mount for DIY Quadcopter Multirotor Pack of 4 Sets Model

Hobbypower CNC Superlight Alloy 16mm Arm Clamp Tube Mount for DIY Quadcopter Multirotor (Pack of 4 Sets) Model:

Hobbypower CNC Superlight Alloy 16mm Arm Clamp Tube Mount for DIY Quadcopter Multirotor (Pack of 4 Sets) Model: - Cnc parts are much lighter and stronger than regular aluminum parts, which is essential to keep your multirotor as light as possible and increased reliability. This auction is for 4 sets of 16mm clamps with bolts and nuts as shown in picture. This is a must for your diy multicoptor. For 16mm diameter tubecolor blackmaterial aluminumcnc super light and strong aluminum clamp for tube. Installed advice 3-axis aircraft need 12 pcsquadcopter need 16 pcs hexacopter need 24 pcs octacopter need 32 pcs.

 

iFLY 1 pc 58GHZ24GHZ TXRX FPV Antenna Mushroom SMA Male inner needle diy quadcopter

iFLY 1 pc 5.8GHZ/2.4GHZ TX/RX FPV Antenna Mushroom SMA Male inner needle diy quadcopter

iFLY 1 pc 5.8GHZ/2.4GHZ TX/RX FPV Antenna Mushroom SMA Male inner needle diy quadcopter - 58 ghz mushroom antenna for transmitter and receiver greatly increase the range and covering of your wireless video transmitting and receiving system. Vswr . Horizontal beamwidth 15-25 vertical beamwidth 15-25 directional diagram vertical connector location bottom. Package included 1 x fpv antenna.

 

Tarot TL250C 250mm Robocat cabon Fiber Quadcopter Frame with Hood Cover for FPV RC Drone DIY Quadcopter

Tarot TL250C 250mm Robocat cabon Fiber Quadcopter Frame with Hood Cover for FPV RC Drone DIY Quadcopter

Tarot TL250C 250mm Robocat cabon Fiber Quadcopter Frame with Hood Cover for FPV RC Drone DIY Quadcopter - 8g video transmitter 5 inches propeller specification approx 270mm motor to motor material, carbon fiber/ fiber glass fuselage removable canopy made from shock-absorbing pc material flying weight -410-430g (battery excluded) color yellow   pacakge included 1 tl250c frame kit. 12a speed controller cc3d & mini kk2. Specification, model tl250c, wheelbase 250mm, material carbon fiber board + plastic hood, tenon aluminum column design, adjustable camera angle, hood adopts retractable design, with anti-vibration landing gear     can be fitted with (not include) 1806 to 2206 sized motors. 1 flight controller 3 to 4s 1500mah lipo battery 32mm cctv camera 5.

 

QWinOut 3DR 915MHz Radio Telemetry Kit for 3DRobotics Standard Version APM APM26 Pixhawk 246 FC DIY Quadcopter FPV

QWinOut 3DR 915MHz Radio Telemetry Kit for 3DRobotics Standard Version APM APM2.6 Pixhawk 2.4.6 FC DIY Quadcopter FPV

QWinOut 3DR 915MHz Radio Telemetry Kit for 3DRobotics Standard Version APM APM2.6 Pixhawk 2.4.6 FC DIY Quadcopter FPV - 3dr telemetry kit specifications, very small size, light weight (under 4 grams without antenna), 915mhz/433 mhz, receiver sensitivity to -121 dbm, transmit power up to 20dbm (100mw), transparent serial link, air data rates up to 250kbps, mavlink protocol framing and status reporting, frequency hopping spread spectrum (fhss), adaptive time division multiplexing (tdm), support for lbt and afa, configurable duty cycle, built in error correcting code (can correct up to 25% data bit errors), demonstrated range of several kilometers with a small omni antenna, can be used with a bi-directional amplifier for even more range, open source firmware, at commands for radio configuration, rt commands for remote radio configuration, adaptive flow control when used with apm, based on hm-trp radio modules, with si1000 8051 micro-controller and si4432 radio module.

 

QWinOut APM 28 APM28 RC Multicopter Flight Controller Board Compass ESC Power Distribution Module BEC for FPV RC Drone DIY Quadcopter

QWinOut APM 2.8 APM2.8 RC Multicopter Flight Controller Board Compass & ESC Power Distribution Module BEC for FPV RC Drone DIY Quadcopter

QWinOut APM 2.8 APM2.8 RC Multicopter Flight Controller Board Compass & ESC Power Distribution Module BEC for FPV RC Drone DIY Quadcopter - Apm is an open source flight control, can you play apm well depend on individual ability. Player must have ability of basic understanding of monolithic integrated circuit, c-language, knowledge of electrical,mechanical, and also needs a certain degree of mental capacity, financial and material resources, energy support. With protective case but no shock absorber. Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer. Package included 1 apm28 flight controller build-in compass with protective case 5 10cm extension lead wire cable male to male 1 current meter motherboard 1 red silicone cord 15cm 1 black silicone cord 15cm 1 xt60 male plug 1 t plug male plug 1 6 pin power supply cable 2 heat shrinkable tube.

 

QWinOut Pro SP Racing F3 Flight Control Acro 6DOF with M8N-GPS M8N GPS OSD Combo for DIY Mini 250 280 210 RC Quadcopter FPV Drone

QWinOut Pro SP Racing F3 Flight Control Acro 6DOF with M8N-GPS M8N GPS OSD Combo for DIY Mini 250 280 210 RC Quadcopter FPV Drone

QWinOut Pro SP Racing F3 Flight Control Acro 6DOF with M8N-GPS M8N GPS OSD Combo for DIY Mini 250 280 210 RC Quadcopter FPV Drone - Sp racing f3acro 6dofflight control set. Note acro version does not have ms5611 barometer and hmc5883 . Programmable led. Ublox gps neo-m8n. 1 x sp racing f3acro 6dofflight control set1 x mini new hm-m8n gsp 1 x mini osd.

 

iFLYÂ DIY Kit iFLY H150mm Mini Full 3K Carbon Fiber FPV Quadcopter FramePCB4pcs iFLYÂ IF1806 2300KV Brushless Motor

iFLY® DIY Kit iFLY H150mm Mini Full 3K Carbon Fiber FPV Quadcopter Frame+PCB+4pcs iFLY® IF1806 2300KV Brushless Motor

iFLY® DIY Kit iFLY H150mm Mini Full 3K Carbon Fiber FPV Quadcopter Frame+PCB+4pcs iFLY® IF1806 2300KV Brushless Motor - The new mini carbon fiber fpv quadcopter air frame is new go to frame for acrobatic fpv sessions the mini is an smaller version of the new mini 150, smallest fpv quad kit today. Its stator construction uses high grade, 02mm silicon steel laminations imported from japan, which is ultra-high temperature 241 c degreepure-copper core-winding for optimum efficiency and power transfer we use high grate japan nmb brand ball bearingso support the shaft and provide a long life. It’s a high efficiency brushless motor with very good price, fit for all diy quadcopter, drone hobbyist we ship good fast from usa warehouse and provide customer service. Performance characteristics high specific strength, high specific modulus, light weight, corrosion resistance, fatigue. All ifly motors use high temperature rated n48sh neodymium sintered-magnets for industry-leading performance.

 

YKS DIY 250 Racing Quadcopter Full Carbon Fiber Frame Kit ARF with Camera

YKS DIY 250 Racing Quadcopter Full Carbon Fiber Frame Kit ARF with Camera

YKS DIY 250 Racing Quadcopter Full Carbon Fiber Frame Kit ARF with Camera - Bundled with 58g 600mw image transmission and 700 line hd ntsc camera. Bundled with emax 1806 motor and electronic speed controller (esc). Yks diy 250 quadcopter kit includes 250 afr rc quadcopter and other necessary components and parts it is ready to fly after you assembled all the components and parts (included) and plug the battery (included). Equipped with rubber damper, high quality and strong ability of shock absorption. Full carbon fiber frame kit, which is ultralight and great intensity.

 

KobwaTM DIY Quadcopter Replacement Frame Arm for DJI F450 F550Black with Kobwas Keyring

Kobwa(TM) DIY Quadcopter Replacement Frame Arm for DJI F450 F550(Black) with Kobwa’s Keyring

Kobwa(TM) DIY Quadcopter Replacement Frame Arm for DJI F450 F550(Black) with Kobwa’s Keyring - Package include 1 x frame arm for f4501 x kobwa’s keyring (with kobwa’s logo)kobwa is a registered trademark ,only kobwa brand authorised online retailer have the “kobwa” original packing and accessory keyring with printed logo. These arms are built from very strong materials, which provides better resistance to damage on hard landings.

 

Meidus Clip 16MM Tube Mount Ultralight Metal Fixture For DIY Quadcopter

Meidus Clip 16MM Tube Mount Ultralight Metal Fixture For DIY Quadcopter

Meidus Clip 16MM Tube Mount Ultralight Metal Fixture For DIY Quadcopter - 100%new and high quality. Length 215cm. These arms are practical and ideal for your quadcopter, which are made from the ultra strong pa66+30gf material that provides better resistance to damage on hard landings. Width 23-40cm. Brand new and good quality.

 

BW 4Pcs DIY Quadcopter Muiltcopter Replacement Frame Arm for DJI Flamewheel F450 F550 Frame Arm white Color white Model

BW® 4Pcs DIY Quadcopter Muiltcopter Replacement Frame Arm for DJI Flamewheel F450 F550 Frame Arm (white) Color: white Model:

BW® 4Pcs DIY Quadcopter Muiltcopter Replacement Frame Arm for DJI Flamewheel F450 F550 Frame Arm (white) Color: white Model: - Made of strong materials, provides better resistance to damage on hard landings. Replacement frame arms for dji flamewheel f450 f550 ( 4 pack). Screw hole diameter 25mm. Weight 40g / pcs color red, black, white. Frame arm size 215 x 4 x 5cm / 85 x 16 x 20inch.

 

QWinOut APM 28 Multicopter Flight Controller Board with Case Compass Extension Cable for FPV RC Drone Multirotor DIY Quadcopter

QWinOut APM 2.8 Multicopter Flight Controller Board with Case Compass & Extension Cable for FPV RC Drone Multirotor DIY Quadcopter

QWinOut APM 2.8 Multicopter Flight Controller Board with Case Compass & Extension Cable for FPV RC Drone Multirotor DIY Quadcopter - Player must have ability of basic understanding of monolithic integrated circuit, c-language, knowledge of electrical,mechanical, and also needs a certain degree of mental capacity, financial and material resources, energy support. With protective case but no shock absorber. Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer. Apm is an open source flight control, can you play apm well depend on individual ability. Package included apm28 flight controller build-in compass with protective case1 10cm extension lead wire cable male to male 5.

 

Mxfans 4Pcs Black Aluminium Alloy 12MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor

Mxfans 4Pcs Black Aluminium Alloy 12MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor

Mxfans 4Pcs Black Aluminium Alloy 12MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor - Specification material aluminium alloy dimension approx. 98×0. It is made of aluminium alloy 2. It is suitable for 12mm diameter tube 3. 20″ weight 20g package included 4 x cnc alloy 12mm tube boom mount motor clamp. 79×0. 25 x 20x 5mm/0. It can keep your multirotor as light as possible. Feature 1.

 

Dayan Anser DIY RC Quadcopter Kit Multicopter Drone Sets Brushless ESC Spare Parts for Syma X8 Series X8X8WX8GX8CX8HWX8HC Can Equip GoPro

Dayan Anser DIY RC Quadcopter Kit Multicopter Drone Sets Brushless ESC Spare Parts for Syma X8 Series X8/X8W/X8G/X8C/X8HW/X8HC Can Equip GoPro

Dayan Anser DIY RC Quadcopter Kit Multicopter Drone Sets Brushless ESC Spare Parts for Syma X8 Series X8/X8W/X8G/X8C/X8HW/X8HC Can Equip GoPro - – done, install camera and enjoy., Install battery,binding remote controller to quadcopter and calibrate to horizontal direction., Connecting brushless motor module to esc, beware the correct direction as below. Package included 4motor, 1screwdriver, 1 bag of screws, 1transmitter board, 1flight control board, 4brushless esc, 1instruction manual, 1hexagon cover., Locking fms by screws. (Note there are the different rotating direction on the propellers, it has to install the correct position according to the picture)- locking motor cover., Install antenna and left/right button., Locking protection frames by screws., Insert the led to the correct direction. How to install the upgrade kit to the quadcopter- taking off quadcopter to pieces, insert switch module and lock by screws., Connecting 4pcs esc to the sockets., Locking 4 light modules., Install the trimmer and stick from original remote controller then install upgraded remote circuit board and lock by screws. How to install the remote controller- take off all the screws in the remote controller and the circuit board., Install batteries, make sure the power light stay on and test the functions., Assemble the upper and lower cover of remote controller and lock by screws., Locking esc and brushless motor modules to bottom quadcopter cover., Weld power wires to the correct direction as pic 5. Specification compatible with syma x8/x8w/x8g/x8c/x8hw/x8hc/huanqi 899/helicute quadcopter(big 4-axis)., Locking landing gear by screws., Assembling upper and lower quadcopter cover- installing quadcopter battery, bind remote controller to the quadcopter., Remove the battery and install the propeller, lock the motor cap.

 

BQLZR DIY Quadcopter Multirotor CNC 12mm Arm Tube Motor Clamp Pack of 4

BQLZR DIY Quadcopter Multirotor CNC 12mm Arm Tube Motor Clamp Pack of 4

BQLZR DIY Quadcopter Multirotor CNC 12mm Arm Tube Motor Clamp Pack of 4 - The interior to accommodate more electronic devices, not only protect the equipment, but also make the whole rack neater appearance. For 12mm diameter tube. Dimension approx 25 x 20x 5mm/079x098x020″. Effectively heightening the fuselage interior space. Material aluminium alloy.

 

RadioLink Remote Control System AT9 24G 9CH Transmitter R9D Receiver for DIY Quadcopter RC Helicopter and Drone

RadioLink Remote Control System AT9 2.4G 9CH Transmitter R9D Receiver for DIY Quadcopter RC Helicopter and Drone

RadioLink Remote Control System AT9 2.4G 9CH Transmitter R9D Receiver for DIY Quadcopter RC Helicopter and Drone - Includes 1x at9 transmitter (model 2) 1x r9d receiver 1x cd manual. 4096 precision, support sbus, usb online upgrade. Built in mini receiver which support and compatible with futaba s-bus. Full types control, ” aircraft” model type added. Dsss, vibration alarm, 3ms quick response.

 

QWinOut APM 28 Multicopter Flight Controller Board with Case Compass Extension Cable for FPV RC Drone Multirotor DIY Quadcopter - Straight pin

QWinOut APM 2.8 Multicopter Flight Controller Board with Case Compass & Extension Cable for FPV RC Drone Multirotor DIY Quadcopter – Straight pin

QWinOut APM 2.8 Multicopter Flight Controller Board with Case Compass & Extension Cable for FPV RC Drone Multirotor DIY Quadcopter – Straight pin - Apm is an open source flight control, can you play apm well depend on individual ability. Player must have ability of basic understanding of monolithic integrated circuit, c-language, knowledge of electrical,mechanical, and also needs a certain degree of mental capacity, financial and material resources, energy support. Package included apm28 flight controller build-in compass with protective case1 10cm extension lead wire cable male to male 5. Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer. With protective case but no shock absorber.

 

uxcell 2Pcs DIY Quadcopter Plastic Propellers Prop 9 Inch for RC Airplane

uxcell 2Pcs DIY Quadcopter Plastic Propellers Prop 9 Inch for RC Airplane

uxcell 2Pcs DIY Quadcopter Plastic Propellers Prop 9 Inch for RC Airplane - Total length(rotating diameter) 9″hub thickness 16mm / 063″. Product name rc airplane propellersvane number 2. Weight 16gpackage content 2pcsx rc airplane propellers. Material plasticcolor orange. Vane model 9″motor shaft hole dia 25mm / 01″, 15mm/ 006″.

 

QWinOut Deluxe Version BarometerMAG PRO SP Racing F3 Flight Controller Integrate OSD with Protective Case for DIY Quadcopter Drone FPV Multicopter

QWinOut Deluxe Version Barometer/MAG PRO SP Racing F3 Flight Controller Integrate OSD with Protective Case for DIY Quadcopter Drone FPV Multicopter

QWinOut Deluxe Version Barometer/MAG PRO SP Racing F3 Flight Controller Integrate OSD with Protective Case for DIY Quadcopter Drone FPV Multicopter - 5mm mounting holes, stm32f303 cpu, 72mhz inc fpu, high-capacity flash (acro and deluxe), mpu6050 accelerometer/gyro ms5611 barometer (deluxe only) hmc5883 compass (deluxe only), 2x 8pin jst-sh sockets (ppm, pwm, serial rx, gpio, adc, 3v, 5v, gnd), 1x 4pin jst-sh socket for swd debugging, 1x 5pin jst-sh socket for flash firmware and configuration (connect to the cp2104 uart to usb tool), 8x 3pin though-holes for pin headers for esc/servo connections, 4x 2pin though-holes for pin headers for 1x serial port and i2c port, 8x 1pin though-holes for pin headers for battery voltage/buzzer/video in/video out package included, 1 x sp racing deluxe version flight controller integrate osd, 1 x protective case, 1 x programmer, 4 x connection cable, pins. Note this version is deluxe version with barometer/mag, the pin is not welded. Some pictures are as reference, product do not include other electronic parts. Specification, 36x36mm board with 30.

 

Mxfans 4Pcs Black Aluminium Alloy 20MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor

Mxfans 4Pcs Black Aluminium Alloy 20MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor

Mxfans 4Pcs Black Aluminium Alloy 20MM Arm Clamp Tube Mount for DIY Quadcopter Multirotor - 34″ weight 30g package include 4 x alloy tube motor clamp. 79″) 2. It is made of aluminium alloy note installed advice 3-axis aircraftneed 12 pcs quadcopter need 16 pcs hexacopter need 24 pcs specification color black material aluminium alloy dimension approx. 1. Suitable for armcarbon nanotubes with diameter of 20mm(0. 2″ hole spacing 30mm/1. 3. 14 x 0. 34 x 1. Keep your multirotor as light as possible. Feature 1.