Best 20 Multi Rotors

 

FS A8S 8 Channels Receiver for Flysky Transmitter Multi-rotor Aircraft #ad

FS A8S 8 Channels Receiver for Flysky Transmitter Multi-rotor Aircraft

FS A8S 8 Channels Receiver for Flysky Transmitter Multi-rotor Aircraft #ad - Fs-a8s is a compact 1-way receiver designed for multi-rotor aircraftcompatible with fs-i4,fs-i6s,fs-i6x,fs-i10 ectfs series rc transmitter. Rf range 2408-2475ghz,bandwidth 500khz,operating current 40ma,power input 40~84v,antenna length 26mm (not including brass contacts) and no ground interference (transmitting and receiving 1m from the ground) >300m. It uses the afhds 2a (automatic frequency hopping digital system) protocol. The fs-a8s supports standard ppm output and i-bus support for up to 18 channels. Notenot included the remote control.

 

Hobbyking Multi-Rotor Power Distribution Board DIY 8 x output PCB #ad

Hobbyking Multi-Rotor Power Distribution Board (DIY 8 x output PCB)

Hobbyking Multi-Rotor Power Distribution Board (DIY 8 x output PCB) #ad - A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your escs and radio and you’re ready to go. Input voltage 48-60v. The kk-mini added polarity protection to the voltage sense header and on-board buzzer the voltage sense line has been updated for better accuracy. The kk2 is next big evolution of the first generation kk flight control boards the kk2 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts the lcd screen and built in software makes install and setup easier than ever a host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your escs and radio and you’re ready to go all of which is done with easy to follow on screen prompts. Signal from receiver 1520us (5 channels) , signal to esc 1520us.

 

Afro Slim 20Amp Multi-rotor Motor Speed Controller SimonK Firmware #ad

Afro Slim 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)

Afro Slim 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware) #ad - This product is a well designed 330mm frame for rc quadcopter. Using high strength compound pcb frame board, which makes wiring of escs and battery more easily. The main material is glass fiber while the arms are constructed from ultra polyamide nylon. Large mounting tabs on main frame bottom plate for easy camera mounting. Flamewheel f330 is a multi-rotor designed for all pilots for fun or ap.

 

RipaFire F450 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter #ad

RipaFire® F450 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter

RipaFire® F450 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter #ad - High quality and strong ability of anti-fall, lower maintenance cost. New design pcb board version fit for standard 50mm controller board such as mk,kk, ff, mwc. It can achieve hovering, cruising, even rolling and other flight elements. Made by advanced engineering material, super strong & smooth f450 frame kit. Suitable for both beginners and senior players, can be applied for entertainment, aerial photography, fpv and other aeromodelling activities.

 

RipaFire F330 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter #ad

RipaFire® F330 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter

RipaFire® F330 4-Axis Multi-Rotor Quadcopter Flame Airframe FrameWheel Rack Kit Support for DJI KK MK MWC RC Quadcopter #ad - With dji wkm or naza autopilot system, it can achieve hovering, cruising, even rolling and other flight elements. Large mounting tabs on main frame bottom plate for easy camera mounting. Suitable for both beginners and senior players, can be applied for entertainment, aerial photography, fpv and other aeromodelling activities. The main material is glass fiber, while the arms are constructed from ultra polyamide nylon. Using high strength compound pcb frame board, which makes wiring of escs and battery more easily.

 

MultiStar LiHV High Capacity 6S 10000mAh Multi-Rotor Lipo Pack #ad

MultiStar LiHV High Capacity 6S 10000mAh Multi-Rotor Lipo Pack

MultiStar LiHV High Capacity 6S 10000mAh Multi-Rotor Lipo Pack #ad - We have a full range of multistar high capacity multi-rotor battery packs in the works and will be adding new sizes/configurations as they become available. This results in a battery which is still capable of providing sufficient current (amps) while offering much higher capacity when compared to a standard 20c+ lipoly battery of the same weight. Overviewhigh voltage lipoly batteries (lihv) offer a significant increase in power density whilst not incurring a weight penalty. This means longer flight times flight times or the ability to carry heavier payloadsmultistar lihv high capacity batteries are the result of extensive testing and development with one goal in mind. . What this all means is that multistar batteries are able to provide flight times much longer than standard lipoly battery packs without adding any weight to your multi-rotor model, making them absolutely ideal for use with aerial video and fpv multi-rotor aircraft. Specsminimum capacity10000mahconfiguration6s1p / 22. Increasing flight times for your multi-rotor aircraft without the penalty of added weight. 8v / 6cellconstant discharge10cpeak discharge (10sec)20cpack weight 1183gpack size168 x 69 x 54mmcharge plugjst-xhdischarge plugnil. We have achieved our goal by drastically increasing the battery capacity (mah) while lowering the discharge rate.

 

YoCoo Mini KK215 Multi-rotor LCD Flight Controller for Flight FPV 250 Quadcopter Multirotor #ad

YoCoo Mini KK2.15 Multi-rotor LCD Flight Controller for Flight FPV 250 Quadcopter Multirotor

YoCoo Mini KK2.15 Multi-rotor LCD Flight Controller for Flight FPV 250 Quadcopter Multirotor #ad - The kk-mini added polarity protection to the voltage sense header and on-board buzzer the voltage sense line has been updated for better accuracy. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your escs and radio and you’re ready to go. The kk-mini is the evolution of the kk215 flight control boards, this new 36mm designed was adapted to fit the needs of the new mini market, but it is has the larger lcd player.  Input voltage 48-60v , net weight 15g. Size 36x36x115mm (mounting holes 305x305mm).

 

Multistar High Capacity 4S 16000mAh Multi-Rotor Lipo Pack #ad

Multistar High Capacity 4S 16000mAh Multi-Rotor Lipo Pack

Multistar High Capacity 4S 16000mAh Multi-Rotor Lipo Pack #ad - Signal from receiver 1520us (5 channels) , signal to esc 1520us. The kk-mini added polarity protection to the voltage sense header and on-board buzzer the voltage sense line has been updated for better accuracy. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your escs and radio and you’re ready to go. The kk2 is next big evolution of the first generation kk flight control boards the kk2 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts the lcd screen and built in software makes install and setup easier than ever a host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your escs and radio and you’re ready to go all of which is done with easy to follow on screen prompts. Input voltage 48-60v.

 

ARRIS Swift Series BLHeli 20A 2-4S BEC 5V1A Brushless ESC for RC Multi-rotor 2PCS #ad

ARRIS Swift Series BLHeli 20A 2-4S BEC 5V/1A Brushless ESC for RC Multi-rotor (2PCS)

ARRIS Swift Series BLHeli 20A 2-4S BEC 5V/1A Brushless ESC for RC Multi-rotor (2PCS) #ad - The firmware is specialized for multi-rotor, fast throtthle response during flying 8 timing setting , makes motors work with the best condition. Blheli firmware, support oneshot 125. Continuous current 20a burst current (10s) 30a. Copy this link to broswer to download the manual http//sitehobby-wingcom/manual/arris-swift-esc-manualpdf. Bec 5v/1a lipo cells 2-4s.

 

AvatarRC Geniune Gemfan 5045 Bullnose 5x45BN Green Propellers for 250 Size Quadcopters Drones and Multi-rotors - Perfect for 210mm to 300mm frames #ad

AvatarRC Geniune Gemfan 5045 Bullnose (5×4.5BN) Green Propellers for 250 Size Quadcopters, Drones, and Multi-rotors – Perfect for 210mm to 300mm frames

AvatarRC Geniune Gemfan 5045 Bullnose (5×4.5BN) Green Propellers for 250 Size Quadcopters, Drones, and Multi-rotors – Perfect for 210mm to 300mm frames #ad - 8 total propellers, 4 clockwise (cw) and 4 counterclockwise (ccw) can properly fly two quad drones or use as spare propellers. Used by some of the best fpv 300, 280, 250, 220, and 210 size racers and pilots. 100% real and genuine high quality gemfan 5045bn (5x45bn) propellers. Mix and match front and rear colors to help fly line-of-sight (los). Very popular size propellers for fpv multirotor racing drones (quadcopters).

 

MultiStar High Capacity 3S 5200mAh Multi-Rotor Lipo Pack for QR X350 PRO #ad

MultiStar High Capacity 3S 5200mAh Multi-Rotor Lipo Pack for QR X350 PRO

MultiStar High Capacity 3S 5200mAh Multi-Rotor Lipo Pack for QR X350 PRO #ad - It uses the afhds 2a (automatic frequency hopping digital system) protocol. Multistar high capacity 3s 5200mah multi-rotor lipo pack. Fs-a8s is a compact 1-way receiver designed for multi-rotor aircraftcompatible with fs-i4,fs-i6s,fs-i6x,fs-i10 ectfs series rc transmitter. The fs-a8s supports standard ppm output and i-bus support for up to 18 channels. Rf range 2408-2475ghz,bandwidth 500khz,operating current 40ma,power input 40~84v,antenna length 26mm (not including brass contacts) and no ground interference (transmitting and receiving 1m from the ground) >300m.

 

MultiStar Race Spec 3S 1400mAh 40-80C Multi-Rotor Lipo Pack For FPV Minis #ad

MultiStar Race Spec 3S 1400mAh 40-80C Multi-Rotor Lipo Pack For FPV Minis

MultiStar Race Spec 3S 1400mAh 40-80C Multi-Rotor Lipo Pack For FPV Minis #ad - Multistar batteries are purpose built for multirotor applications, each tailored for the best size/power/weight needed for their intended use. The new race spec 1400mah high c battery by multistar, get your goggles on and 321 set gospecscapacity 1400mahconfiguration 3s1p / 11. Multistar delivers again for the mini market with a pack for high power 250 fpv racer quadsthese little fpv machines crave for a bit better run time and high c demands that the high kv motors can pull. With 1400mah of capacity and 40-80c discharge ability, your mini racer will feel like its on race fuel the best feature is the size and weight all this power in a frame friendly form factor, even smaller than some 1300mah packs the race spec also comes with the new xt30 connector capable of delivering 30a constant and bursting past when needed. 1500mah is too big and heavy and 1300mah leaves some flights a little short winded. 1v / 3cellconstant discharge 40cpeak discharge (10sec) 80cpack weight 115gpack size 86 x 34 x 20mmcharge plug jst-xhdischarge plug xt30. The new multistar 1400 race spec 3s battery is the winning ticket.

 

Afro ESC 30Amp OPTO Multi-rotor Motor Speed Controller SimonK Firmware #ad

Afro ESC 30Amp OPTO Multi-rotor Motor Speed Controller (SimonK Firmware)

Afro ESC 30Amp OPTO Multi-rotor Motor Speed Controller (SimonK Firmware) #ad - Configuration 4s2p / 148v / 4 cell. Constant discharge 10c. Booole inc researches and develops electronic products and open source hardware with the aim of promoting maker space and diy practice it makes you believe innovation and invention are no more exclusive to scientific research institutes. Discharge plug xt90.

 

SHINA EMAX 4 in 1 Quattro 30A X 4 UBEC Multi-rotor Brushless ESC Quadcopter EE01-30A #ad

SHINA EMAX 4 in 1 Quattro 30A X 4 UBEC Multi-rotor Brushless ESC Quadcopter EE01-30A

SHINA EMAX 4 in 1 Quattro 30A X 4 UBEC Multi-rotor Brushless ESC Quadcopter EE01-30A #ad - Description features, upgraded from simonk firmware, low voltage protection, overheat protection and self-check functions, integrated 4 escs, and only one set of power supply input wire is needed, seperate power board, ubec board, and control board, easy to replace power board, so you can obtain a drive current of 425a or 430a by changing power board, simple and orderly design, be compatible with many types of receivers, high efficiency ubec.

 

New Afro ESC 12 Amp Multi-rotor Speed Controller SimonK quadcopter UBEC Lite 12a Version 3 #ad

New Afro ESC 12 Amp Multi-rotor Speed Controller SimonK quadcopter UBEC Lite 12a Version 3

New Afro ESC 12 Amp Multi-rotor Speed Controller SimonK quadcopter UBEC Lite 12a Version 3 #ad - Bec 05a linear 50v. Input freq 1khz. Weight 10g (included wire, plug, heat shrink) => size 25 x 20 x 6mm. Wire/plugs discharge 20awg/male 2mm => motor 20awg/female 2mm. Current draw 12a continuous => voltage range 2-4s lipoly.

 

Afro ESC 20Amp Multi-rotor Motor Speed Controller SimonK Firmware #ad

Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)

Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware) #ad - 5a linearinput freq 1khzfirmware afro_nfet. The afro esc series ship with multi-rotor specific simonk software preloaded no need to reflash. Specscurrent draw 20a continuousvoltage range 2-4s lipolybec 0. For added convenience the turnigy usb linker can be used via the pwm signal lead for any future software updates eliminating the need for complicated flashing jigs or the need to cut open the heat shrink. We wiped the slate clean and looked to the community for inspiration and help in designing an esc that truly could be known as the multi-rotor escenter simon and hamasaki aka simonk and timecop. Now shipping with oneshot125. 5mmweight 22. Developed from the ground up, we wanted to build a truly multi-rotor specific esc that would offer the best performance and value in the market today. 7 x 10. Boasting high efficiency, all n-channel mosfet design, jitter-free hardware pwm input, and smooth power response the afro esc series are set to change the expectations of multi-rotor pilots around the globe. 8g (included wire, plug, heat shrink)size 45 x 25. 5mmroyalties paid on each unit sold to simonk and hamasaki for their design work, without which the afro esc would never have been born, thanks guys. This combination of hardware and firmware expertise in conjunction with the hobbyking in house engineering team gave us the edge needed to develop an esc like no other and hence the afro series was born. Hexdischarge wire/plugs 16awg/male 3. A diy port is available under the shrink wrap which allows using the esc with mikrokopter hardware that uses i2c control. Some stocks may require to flash esc to oneshot125 via flash tool referenced in the related items. 5mmmotor wire/plugs 16awg/female 3. Mikrokopter i2c compatibility has also been built in as standard.

 

TBS POWERCUBE - MULTI ROTOR STACK #ad

TBS POWERCUBE – MULTI ROTOR STACK

TBS POWERCUBE – MULTI ROTOR STACK #ad - It is the new standard for performance, reliability, ease-of use and cost in race machines. Details stacked compact, a all-in-one power package for your fpv racer between 180 and 330 size. Specifications stm32 f3 flight controller running betaflight regulated and filtered power for cam and vtx (5v/12v/vbatt switchable) 20a continuous, 30a with airflow, 50a peak esc (each) 2-6s capable power distribution 120a continuous current sensor 100a sense, 250a peak throughput dimensions 36mm x 36mm x 30mm weight 70g incl. Optimized for centralized weight distribution stm32f3-based fc, faster and more memory most reliable esc in the industry blheli 14. The colibri race is a f3 based flight controller with enough processing power and memory to achieve low looptimes. Main highlights include features all-in-one, solder-free system for race quads. 1, simonk compatible patented power distribution clean, filtered power for fpv camera and video transmitter, selectable between 5v/12v and vbatt. 2-6s capable, 20a unventilated, 30a continuous, 45a burst escs provide ample juice. The escs are tbs designs based on our bulletproof technology, running the most common firmware blheli and simonk as well. The tbs powercube combines knowledge and experience from over 2 years of research. Pdb, wires & connectors includes tbs powercube stack with flight control, 4x escs, pdb terminating plastic shoe to isolate the tbs powercube from carbon fiber frames cables for fpv camera and video transmitter external 5v buzzer led pigtail cable. Comes with, or plugs into, everything you need.

 

AvatarRC Geniune Gemfan 5030 5x3 Black Propellers for 250 Size Quadcopters and Multi-rotors - Perfect for 210mm to 300mm frames #ad

AvatarRC Geniune Gemfan 5030 (5×3) Black Propellers for 250 Size Quadcopters and Multi-rotors – Perfect for 210mm to 300mm frames

AvatarRC Geniune Gemfan 5030 (5×3) Black Propellers for 250 Size Quadcopters and Multi-rotors – Perfect for 210mm to 300mm frames #ad - Used by some of the best fpv 250 racers and pilots. 100% real and genuine high quality gemfan 5030 (5×3) propellers. Most popular size propellers for fpv 250 class racers like zmr250, blackout 250, blackout mini, and other quad kits. Get longer flight time than comparable 5″ propellers. 8 total propellers, 4 clockwise (cw) and 4 counterclockwise (ccw) can properly fly two quad drones or use as spare propellers.

 

HobbyKing KK215 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA #ad

HobbyKing KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA

HobbyKing KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA #ad - Customer service is our top priority, and while some issues are beyond our control, we do our best to ensure your transaction exceeds your expectations. We’re always developing and sourcing new model products and then bringing them to you. All the items shipped from usa including a receipt in the package for custom if need. Should you have an issue with any of our products or service, please contact us vis message. If you love radio control products, then we’re just like you.

 

T-MOTOR MN3510 KV630 High-Performance Brushless Electric Motor for Multi-Rotor Aircraft #ad

T-MOTOR MN3510 KV630 High-Performance Brushless Electric Motor for Multi-Rotor Aircraft

T-MOTOR MN3510 KV630 High-Performance Brushless Electric Motor for Multi-Rotor Aircraft #ad - This cuts down on vibrations that can negatively affect aerial video and autopilot inertial sensors. , T-motors are smooth running and well balanced right out of the box. T-motors are backed by a two-year manufacturer’s warranty on materials and workmanship. See photo library above for detailed spec sheet and dimensional cad drawing. Featuring precision workmanship and ezo® bearings from world renowned japanese bearing manufacturer sapporo precision, inc. This mn3510 kv630 motor is recommended for use with 3 to 4s lipo and 12×4 to 14×4. 8 props. Tiger motors t-motor mn3510 kv630 is a high-performance brushless motor specifically designed for use on multi-rotor aircraft such as quadcopters and hexacopters. With epoxy-coated kawasaki stator plates for low eddy current loss, oxygen-free copper windings for low resistance, and n45uh high-temperature neodymium magnets, t-motors are highly efficient and can maintain good performance even up to 180° c.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.